亚洲精品鲁一鲁一区二区三区-最爽无遮挡行房视频-强壮的公次次弄得我高潮A片日本-精品人妻无码一区二区三区换脸-中文字幕亚韩-亚洲国产精品一区二区第一页-丰满岳乱妇一区二区三区-大陆极品少妇内射AAAAAA-国产乱人伦AV麻豆网-AV国産精品毛片一区二区三区-午夜精品视频在线无码-免费精品一区二区三区A片在线-在线天堂无限次观看,亚洲日韩无码一区二区,中文字幕乱人伦视频在线,亚洲欧美熟妇综合久久久久久,少妇无码一区二区三区免费久久,欧美黑人一级片在线观看,久久久精品无码一区三区,国产视频在线观看蜜芽,大香蕉五月婷婷精品视频 ,久草精品在线,国产无码在线播放一区二区,囯产无码交换大片在线播放,八戒八戒在线高清观看视频 ,娇妻被又粗又长又猛玩,国产曰肥老太婆无遮挡,国产剧情黄色,国产成年无码久久久久毛片資訊,大香蕉太香蕉成人现现,逼逼爱爱爱无码免费观看,亚州色图欧美图片自偷自拍,碰碰视频麻豆,午夜一本,一起射综合影院,黑人干熟女,欧洲高清转码区一二区 ,国产高清视频色拍,粉嫩无码小泬无套在线观看,大香蕉在线网站,成人做爰理论片,成人漫,9l视频自拍九色9l成人

1. The flange sealing gasket adopts 5mm rubber plate or 8501 flame retardant sealing tape.

2.鍍鋅風管的咬合縫、鉚釘縫、法蘭翻邊四角等縫隙涂有密封膠(如中性玻璃膠)。涂密封膠前，應清除表面灰塵和油污。

2. Sealant (such as neutral glass adhesive) is applied to the seams of galvanized air ducts, such as bite seams, rivet seams, and flange flanges. Before applying sealant, surface dust and oil stains should be removed.

3.法蘭螺孔與鉚釘孔之間的距離不得大于100mm。矩形法蘭的四角應設置螺孔。彎頭、三通等管件的導流片應用平頭鉚釘固定。嚴禁使用抽芯鉚釘。在鉚釘上涂上密封膠。

The distance between flange screw holes and rivet holes shall not exceed 100mm. The four corners of the rectangular flange should be equipped with screw holes. The guide vanes of pipes such as elbows and tees should be fixed with flat headed rivets. It is strictly prohibited to use pop rivets. Apply sealant to the rivets.

4.鍍鋅風管與法蘭連接時，翻邊應平整緊貼法蘭，寬度不小于7mm。

When connecting the galvanized air duct to the flange, the flange should be flat and tightly pressed against the flange, with a width of no less than 7mm.

5.軟接頭采用角鋼法蘭連接。

5. The soft joint is connected with angle steel flanges.

6.角鋼法蘭連接鍍鋅風管。

6. Angle steel flange connection galvanized air duct.

7.鍍鋅風管的咬口形式為單咬口和聯合角咬口。

7. The bite forms of galvanized air ducts are single bite and joint angle bite.

8.鍍鋅風管直管的制造應盡量減少縱向拼接縫，不得有橫向拼接縫。當邊長小于或等于900mm時，底板不得有拼接縫，大于900mm時不得有橫向拼接縫。

8. The manufacturing of galvanized air ducts and straight pipes should minimize longitudinal seams as much as possible, and there should be no transverse seams. When the side length is less than or equal to 900mm, the bottom plate shall not have splicing joints, and when it is greater than 900mm, there shall be no transverse splicing joints.

9.當板材尺寸能滿足下料要求，損耗率不會太大時，可以考慮將彎頭、三通等配件與直線段連接，減少法蘭接口。

When the plate size can meet the cutting requirements and the loss rate is not too high, it can be considered to connect elbows, tees, and other accessories to the straight section to reduce flange interfaces.

本文由濟南通風管道友情奉獻.更多有關的知識請點擊:   http://www.wxcdx.com 真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待

This article is dedicated by Jinan Ventilation Pipeline Friendship. For more relevant knowledge, please click on: http://www.wxcdx.com Sincere attitude. We will provide you with comprehensive services. We will gradually contribute more relevant knowledge to everyone. Stay tuned