亚洲精品鲁一鲁一区二区三区-最爽无遮挡行房视频-强壮的公次次弄得我高潮A片日本-精品人妻无码一区二区三区换脸-中文字幕亚韩-亚洲国产精品一区二区第一页-丰满岳乱妇一区二区三区-大陆极品少妇内射AAAAAA-国产乱人伦AV麻豆网-AV国産精品毛片一区二区三区-午夜精品视频在线无码-免费精品一区二区三区A片在线-在线天堂无限次观看,亚洲日韩无码一区二区,中文字幕乱人伦视频在线,亚洲欧美熟妇综合久久久久久,少妇无码一区二区三区免费久久,欧美黑人一级片在线观看,久久久精品无码一区三区,国产视频在线观看蜜芽,大香蕉五月婷婷精品视频 ,久草精品在线,国产无码在线播放一区二区,囯产无码交换大片在线播放,八戒八戒在线高清观看视频 ,娇妻被又粗又长又猛玩,国产曰肥老太婆无遮挡,国产剧情黄色,国产成年无码久久久久毛片資訊,大香蕉太香蕉成人现现,逼逼爱爱爱无码免费观看,亚州色图欧美图片自偷自拍,碰碰视频麻豆,午夜一本,一起射综合影院,黑人干熟女,欧洲高清转码区一二区 ,国产高清视频色拍,粉嫩无码小泬无套在线观看,大香蕉在线网站,成人做爰理论片,成人漫,9l视频自拍九色9l成人

風管及管道部件設計過程中常用的計算方法您知道是怎樣的嗎？實際上對于業余人員來講，可能不太好理解，但還是建議您在使用之前多來了解，下面山東通風管道廠家為你解答：

Do you know the common calculation methods used in the design of duct and pipe components? In fact, it may not be easy for amateurs to understand, but it is still recommended that you learn more before use. The following is the answer from Shandong ventilation pipe manufacturer:

1.

one

風管安裝按施工圖示不同規格以展開“面積”計算，不扣除檢查孔、測定孔、送風口、吸風口等所占面積。

The air duct installation shall be calculated based on the "area" of different specifications in the construction drawing, excluding the area occupied by inspection holes, measuring holes, air supply outlets, suction outlets, etc.

計算風管長度時，一律以施工圖示線長度為準（主管與支管以其線交點劃分），包括彎頭、三通、變徑管、天圓地方等管件的長度，但不得包括帆布、風閥、消聲器、設備所占長度。直徑和周長按圖示尺寸為準展開。

When calculating the length of the air duct, the length of the center line in the construction drawing shall prevail (the main pipe and the branch pipe shall be divided by the intersection of the center line), including the length of the elbow, tee, reducing pipe, the radius of the sky and other pipe fittings, but not including the length of canvas, air valve, muffler, and equipment. The diameter and perimeter shall be expanded according to the dimensions shown in the figure.

報價時定額已含損耗，計算結果不需要乘損耗系數。

The quota includes loss when quoting, and the calculation result does not need to be multiplied by loss factor.

2.

two

薄鋼板通風管道、凈化通風管道，復合型風管（玻纖板、不燃無機復合風管），報價定額內已包括法蘭、加固框和吊托支架，不另行計算。但不包括過跨風管落地支架，因此過跨風管落地支架需按圖按規范計算重量。

Thin steel plate ventilation duct, purification ventilation duct, composite air duct (fiberglass board, incombustible inorganic composite air duct), flanges, reinforcement frame and lifting bracket have been included in the quotation quota, and are not calculated separately. However, it does not include the over-span air duct floor support, so the weight of the over-span air duct floor support shall be calculated according to the drawing and specifications.

3.

three

不銹鋼通風管道、鋁板通風管道，風管咬口連接中報價定額包括管件、法蘭，但不包括吊托支架，焊接連接中報價定額僅包括管件，不包括法蘭和吊托支架，其工程量以“kg”為計量單位，故根據風管連接方式按設計說明或規范計算法蘭和吊托支架重量。

For stainless steel ventilation pipes and aluminum plate ventilation pipes, the quotation quota in the air duct seaming connection includes pipe fittings and flanges, but does not include lifting brackets. The quotation quota in the welding connection only includes pipe fittings, but does not include flanges and lifting brackets. The work quantity is measured in "kg". Therefore, the weight of flanges and lifting brackets is calculated according to the air duct connection method and the design instructions or specifications.

參考已施工項目結算數據：法蘭（不銹鋼角鐵3#）的含量測算0.9kg/m2；吊托支架（不銹鋼角鐵4#、不銹鋼槽鋼6#）含量測算1.5kg/m2；若其他項目有類似工程請及時提供數據及時更正。

Refer to the settlement data of the constructed project: the content of flange (stainless steel angle iron 3 #) is estimated to be 0.9kg/m2; The content of lifting bracket (stainless steel angle iron 4 #, stainless steel channel steel 6 #) is estimated to be 1.5kg/m2; If there are similar projects in other projects, please provide data timely for correction.

4.

four

風管軟接：

Flexible connection of air duct:

（1）帆布接口，按圖示尺寸以“平方米”計算，一般寬度為250mm，具體以現場制作經驗考慮；

(1) The canvas interface is calculated in "square meters" according to the size shown in the figure, and the general width is 250mm, which is based on the site production experience;

（2）軟管風管，按圖紙尺寸以“米”計算。

(2) The hose duct is calculated in "m" according to the drawing size.

5.

five

風管導流葉片，按風管規格計算彎頭個數，按下表計算導流葉片“面積”。

For the guide vane of air duct, calculate the number of elbows according to the specification of air duct, and calculate the "area" of guide vane according to the following table.

6.

six

風口風閥，按不同類型（防火閥、蝶閥、對開多葉閥、散流器、百葉等）不同規格以“個”為計量單位（按成品計算）。

The unit of measurement is "piece" (calculated as finished product) according to different types (fire damper, butterfly valve, split multi-leaf valve, diffuser, louver, etc.) and different specifications.

7.

seven

消聲器、消聲靜壓箱、靜壓箱，按不同規格以“臺”為計量單位（按成品計算），除設計要求現場制作時以“平方米”（展開六個面面積）計算。

Silencer, silencing static pressure box and static pressure box shall be measured by "set" (calculated by finished product) according to different specifications, and shall be calculated by "square meter" (six surface areas) except for the design requirements.

8.

eight

防蟲網以“個”計算或者以“平方米”計算，組價人員可根據需要自行換算。

The insect-proof net is calculated in "pieces" or "square meters", and the pricing personnel can convert it according to their needs.

9.

nine

設計說明有需要風管檢查孔與風管測定孔的，檢查孔按下表換算，以重量計算，測定孔按其型號以“個”為計量單位。

If the design specification requires air duct inspection hole and air duct measuring hole, the inspection hole shall be converted according to the following table and calculated by weight, and the measuring hole shall be measured in "piece" according to its model.

10.

ten

過墻套管采用2mm厚鋼板或其他厚度時（按設計圖紙）以“面積”計算。

When the wall casing adopts 2mm thick steel plate or other thickness (according to the design drawing), it is calculated by "area".

關于風管及管道部件設計中常用的計算方法，咱們就了解到這里了，十個方面的要點希望能夠帶給您一定的信息了解，更多事項歡迎前來咨詢我們http://www.wxcdx.com！

We have learned about the commonly used calculation methods in the design of air duct and pipe components. We hope that the ten key points can give you some information. For more matters, please come to consult us http://www.wxcdx.com ！